Using the "Damper" member type, you can define a damping coefficient, a spring constant, and a mass. This member type extends the possibilities within the Time History Analysis.
With regard to viscoelasticity, the "Damper" member type is similar to the Kelvin-Voigt model, which consists of the damping element and an elastic spring (both connected in parallel).
The "Spring" member type is used to simulate linear and nonlinear spring properties via a linear object. This input function helps you to model the stiffness specifications in the force/displacement unit.
Would you like to calculate curved beams (for example, made of glued-laminated timber)? For this purpose, you can use various section distributions for members:
The pushover analysis is managed by a newly introduced analysis type in the load combinations. Here, you have access to the selection of the horizontal load distribution and direction, the selection of a constant load, the selection of the desired response spectrum for the determination of the target displacement, and the pushover analysis settings tailored to the pushover analysis.
In the pushover analysis settings, you can modify the increment of the increasing horizontal load and specify the stopping condition for the analysis. Furthermore, it is possible to easily adjust the precision for the iterative determination of the target displacement.
Consideration of nonlinear component behavior using plastic standard hinges for steel (FEMA 356, EN 1998‑3) and nonlinear material behavior (masonry, steel - bilinear, user-defined working curves)
Direct import of masses from load cases or combinations for the application of constant vertical loads
User-defined specifications for the consideration of horizontal loads (standardized to a mode shape or uniformly distributed over the height of the masses)
Determination of a pushover curve with selectable limit criterion of the calculation (a collapse or limit deformation)
Transformation of the pushover curve into the capacity spectrum (ADRS format, single degree of freedom system)
Bilinearization of the capacity spectrum according to EN 1998‑1:2010 + A1:2013
Transformation of the applied response spectrum into the required spectrum (ADRS format)
Determination of target displacement according to EC 8 (the N2 method according to Fajfar 2000)
Graphical comparison of the capacity and required spectrum
Graphical evaluation of the acceptance criteria of predefined plastic hinges
Result display of the values used in the iterative calculation of the target displacement
Access to all results of the structural analysis in the individual load levels
For timber surfaces with the "Constant" thickness type, the crack factor kcr and thus the negative influence of cracks on the shear capacity is taken into account.
Are you familiar with the Tsai-Wu material model? It combines plastic and orthotropic properties, which allows for special modeling of materials with anisotropic characteristics, such as fiber-reinforced plastics or timber.
If the material is plastified, the stresses remain constant. The redistribution is carried out according to the stiffnesses available in the individual directions. The elastic area corresponds to the Orthotropic | Linear Elastic (Solids) material model. For the plastic area, the yielding according to Tsai-Wu applies:
All strengths are defined positively. You can imagine the stress criterion as an elliptical surface within a six-dimensional space of stresses. If one of the three stress components is applied as a constant value, the surface can be projected onto a three-dimensional stress space.
If the value for fy(σ), according to the Tsai-Wu equation, plane stress condition, is smaller than 1, the stresses are in the elastic zone. The plastic area is reached as soon as fy (σ) = 1; values greater than 1 are not allowed. The model behavior is ideal-plastic, which means there is no stiffening.
One thing is absolutely undisputed: WebService and API covers universal aspects in the construction industry. However, there is an issue. For the calculation and design, you need different features for each region, country, company, and civil engineer. Everyone has their own requirements. We have solved this problem. Since with WebService and API, you can easily create your very own calculation and design system. Always at your side: The performance and reliability of RFEM, RSTAB, and RSECTION.
The need for adapted and automated structural analysis and design is constantly increasing. WebService technology allows you to create special functionalities quickly and precisely. Our customers can develop such solutions independently or in cooperation with us. See for yourself and give it a try!
Compared to the RF-/STEEL Warping Torsion add-on module (RFEM 5 / RSTAB 8), the following new features have been added to the Torsional Warping (7 DOF) add-on for RFEM 6 / RSTAB 9:
Complete integration into the environment of RFEM 6 and RSTAB 9
7th degree of freedom is directly taken into account in the calculation of members in RFEM/RSTAB on the entire system
No more need to define support conditions or spring stiffnesses for calculation on the simplified equivalent system
Combination with other add-ons is possible, for example for the calculation of critical loads for torsional buckling and lateral-torsional buckling with stability analysis
No restriction to thin-walled steel sections (it is also possible to calculate ideal overturning moments for beams with massive timber sections, for example)
Import of relevant information and results from RFEM
Integrated, editable material and section library
Sensible and complete presetting of input parameters
Punching design on columns (all section shapes), wall ends, and wall corners
Automatic recognition of the punching node position from an RFEM model
Detection of curves or splines as a boundary of the control perimeter
Automatic consideration of all slab openings defined in the RFEM model
Construction and graphical display of the control perimeter
Optional design with unsmoothed shear stress along the control perimeter that corresponds to the actual shear stress distribution in the FE model
Determination of the load increment factor β via full-plastic shear distribution as constant factors according to EN 1992‑1‑1, Sect. 6.4.3 (3), based on EN 1992‑1‑1, Fig. 6.21N, or by a user‑defined specification
Numerical and graphical display of results (3D, 2D, and in sections)
Punching design of the slab without punching reinforcement
Qualitative determination of the required punching reinforcement
Design and analysis of the longitudinal reinforcement
Complete integration of results in an RFEM printout report
Consideration of 7 local deformation directions (ux, uy, uz, φx, φy, φz, ω) or 8 internal forces (N, Vu, Vv, Mt,pri, Mt,sec, Mu, Mv, Mω) when calculating member elements
Usable in combination with a structural analysis according to linear static, second-order, and large deformation analysis (imperfections can also be taken into account)
In combination with the Stability Analysis add-on, allows you to determine critical load factors and mode shapes of stability problems such as torsional buckling and lateral-torsional buckling
Consideration of end plates and transverse stiffeners as warping springs when calculating I-sections with automatic determination and graphical display of the warping spring stiffness
Graphical display of the cross-section warping of members in the deformation
You can perform the calculation of the warping torsion on the entire system. Thus, you consider the additional 7th degree of freedom in the member calculation. The stiffnesses of the connected structural elements are automatically taken into account. It means, you don't need to define equivalent spring stiffnesses or support conditions for a detached system.
You can then use the internal forces from the calculation with warping torsion in the add-ons for the design. Consider the warping bimoment and the secondary torsional moment, depending on the material and the selected standard. A typical application is the stability analysis according to the second-order theory with imperfections in steel structures.
Did you know that The application is not limited to thin-walled steel cross-sections. Thus, it is possible for you, for example, to perform the calculation of the ideal overturning moment of beams with solid timber cross-sections.
If you are working with nonlinearities, this feature is suited very well to support you. For example, you can specify nonlinearities of member end releases (yielding, tearing, slippage, and so on) and supports (including friction). Furthermore, you can use special dialog boxes to determine the spring stiffnesses of columns and walls based on the geometry specifications.
In STEEL AISC, it is possible to consider lateral intermediate supports at any location. For example, it is possible to stabilize only the upper flange.
Furthermore, user-defined lateral intermediate supports can be assigned; for example, single rotational springs and translational springs at any location at the cross-section.
Beam to Column joint category: connection possible as joint of the beam to the column flange as well as joint of the column to the girder flange
Beam to Beam joint category: design of beam joints as both moment-resisting end plate connections and rigid splice connections possible
Automatic export of model and load data possible from RFEM or RSTAB
Bolt sizes from M12 to M36 with strength grades 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, and 10.9 as long as the strength grades are available in the selected National Annex
Almost any bolt spacing and edge distances (a check of the allowable distances is performed)
Beam strengthening with tapers or stiffeners on the top and bottom surfaces
End plate connection with and without overlap
Connection with pure bending stress, pure normal force load (tension joint), or combination of normal force and bending possible
Calculation of connection stiffnesses and check if a hinged, semi-rigid, or rigid connection exists
End plate connection in a beam-column setup
Joint beams or columns can be stiffened with tapers on one side or with stiffeners to one or both sides
Wide range of possible stiffeners of the connection (for example, complete or incomplete web stiffeners)
Up to ten horizontal and four vertical bolts possible
Connected object possible as constant or tapered I-section
Designs:
Ultimate limit state of the connected beam (such as shear or tension resistance of the web plate)
Ultimate limit state of the end plate at the beam (for example, T-stub under tensile stress)
Ultimate limit state of the welds at the end plate
Ultimate limit state of the column in the area of the connection (for example, column flange under bending – T-stub)
All designs are performed according to EN 1993-1-8 and EN 1993-1-1
Moment-resisting end plate joint
Two or four vertical and up to 10 horizontal bolt rows
Joint beams can be stiffened with tapers on one side or with stiffeners to one or both sides
Connected objects are possible as constant or tapered I-sections
Designs:
Ultimate limit state of the connected beams (such as shear or tension resistance of the web plates)
Ultimate limit state of the end plates at the beam (for example, T-stub under tensile stress)
Ultimate limit state of the welds at the end plates
Ultimate limit state of the bolts in the end plate (combination of tension and shear)
Rigid splice plate connection
For the flange plate connection, up to ten bolt rows one behind the other possible
For the web plate connection, up to ten bolt rows possible each in vertical and horizontal directions
Material of the cleat can be different from the one of the beams
Designs:
Ultimate limit state of the joint beams (for example, net cross-section in the tension area)
Ultimate limit state of the cleat plates (for example, net cross-section under tensile stress)
Ultimate limit state of the single bolts and the bolt groups (for example, shear resistance design of the single bolt)
The member type 'Dashpot' can be used for time history analyzes in RFEM/RSTAB with the add-on modules RF-/DYNAM Pro - Forced Vibrations and RF-/DYNAM Pro - Nonlinear Time History. This linear viscous damping element considers forces dependent on velocity.
With regard to viscoelasticity, the member type 'Dashpot' is similar to the Kelvin-Voigt model, which consists of the damping element and an elastic spring (both connected in parallel).
Import of materials, cross-sections, and internal forces from RFEM/RSTAB
Steel design of thin‑walled cross‑sections according to EN 1993‑1‑1:2005 and EN 1993‑1‑5:2006
Automatic classification of cross-sections according to EN 1993-1-1:2005 + AC:2009, Cl. 5.5.2, and EN 1993-1-5:2006, Cl. 4.4 (cross-section class 4), with optional determination of effective widths according to Annex E for stresses under fy
Integration of parameters for the following National Annexes:
DIN EN 1993-1-1/NA:2015-08 (Germany)
ÖNORM B 1993-1-1:2007-02 (Austria)
NBN EN 1993-1-1/ANB:2010-12 (Belgium)
BDS EN 1993-1-1/NA:2008 (Bulgaria)
DS/EN 1993-1-1 DK NA:2015 (Denmark)
SFS EN 1993-1-1/NA:2005 (Finland)
NF EN 1993-1-1/NA:2007-05 (France)
ELOT EN 1993-1-1 (Greece)
UNI EN 1993-1-1/NA:2008 (Italy)
LST EN 1993-1-1/NA:2009-04 (Lithuania)
UNI EN 1993-1-1/NA:2011-02 (Italy)
MS EN 1993-1-1/NA:2010 (Malaysia)
NEN EN 1993-1-1/NA:2011-12 (Netherlands)
NS EN 1993-1-1/NA:2008-02 (Norway)
PN EN 1993-1-1/NA:2006-06 (Poland)
NP EN 1993-1-1/NA:2010-03 (Portugal)
SR EN 1993-1-1/NB:2008-04 (Romania)
SS EN 1993-1-1/NA:2011-04 (Sweden)
SS EN 1993-1-1/NA:2010 (Singapore)
STN EN 1993-1-1/NA:2007-12 (Slovakia)
SIST EN 1993-1-1/A101:2006-03 (Slovenia)
UNE EN 1993-1-1/NA:2013-02 (Spain)
CSN EN 1993-1-1/NA:2007-05 (Czech Republic)
BS EN 1993-1-1/NA:2008-12 (the United Kingdom)
CYS EN 1993-1-1/NA:2009-03 (Cyprus)
In addition to the National Annexes (NA) listed above, you can also define a specific NA, applying user‑defined limit values and parameters.
Automatic calculation of all required factors for the design value of flexural buckling resistance Nb,Rd
Automatic determination of the ideal elastic critical moment Mcr for each member or set of members on every x-location according to the Eigenvalue Method or by comparing moment diagrams. You only have to define the lateral intermediate supports.
Design of tapered members, unsymmetric sections or sets of members according to the General Method as described in EN 1993-1-1, Cl. 6.3.4
In the case of the General Method according to Cl. 6.3.4, optional application of "European lateral-torsional buckling curve" according to Naumes, Strohmann, Ungermann, Sedlacek (Stahlbau 77 [2008], pp. 748‑761)
Rotational restraints can be taken into account (trapezoidal sheeting and purlins)
Optional consideration of shear panels (for example, trapezoidal sheeting and bracing)
RF-/STEEL Warping Torsion module extension (license required) for stability analysis according to the second-order analysis as stress analysis including consideration of the 7th degree of freedom (warping)
Module extension RF-/STEEL Plasticity (license required) for plastic analysis of cross‑sections according to Partial Internal Forces Method (PIFM) and Simplex Method for general cross‑sections (in connection with the RF‑/STEEL Warping Torsion module extension, it is possible to perform the plastic design according to the second‑order analysis)
Module extension RF-/STEEL Cold-Formed Sections (license required) for ultimate and serviceability limit state designs for cold-formed steel members according to the EN 1993-1-3 and EN 1993-1-5 standards
ULS design: Selection of fundamental or accidental design situations for each load case, load combination, or result combination
SLS design: Selection of characteristic, frequent, or quasi-permanent design situations for each load case, load combination, or result combination
Tension analysis with definable net cross-section areas for member start and end
Weld designs of welded cross-sections
Optional calculation of warp spring for nodal support on sets of members
Graphic of design ratios on cross-section and in RFEM/RSTAB model
Determination of governing internal forces
Filter options for graphical results in RFEM/RSTAB
Representation of design ratios and cross‑section classes in the rendered view
Color scales in result windows
Automatic cross-section optimization
Transfer of optimized cross-sections to RFEM/RSTAB
Parts lists and quantity surveying
Direct data export to MS Excel
Verifiable printout report
Possibility to include the temperature curve in the report
Import of relevant information and results from RFEM
Integrated, editable material and section library
The module extension EC2 for RFEM enables the design of reinforced concrete members according to EN 1992‑1‑1:2004 (Eurocode 2) and the following National Annexes:
DIN EN 1992-1-1/NA/A1:2015-12 (Germany)
ÖNORM B 1992-1-1:2018-01 (Austria)
NBN EN 1992-1-1 ANB:2010 (Belgium)
BDS EN 1992-1-1:2005/NA:2011 (Bulgaria)
EN 1992-1-1 DK NA:2013 (Denmark)
NF EN 1992-1-1/NA:2016-03 (France)
SFS EN 1992-1-1/NA:2007-10 (Finland)
UNI EN 1992-1-1/NA:2007-07 (Italy)
LVS EN 1992-1-1:2005/NA:2014 (Latvia)
LST EN 1992-1-1:2005/NA:2011 (Lithuania)
MS EN 1992-1-1:2010 (Malaysia)
NEN-EN 1992-1-1+C2:2011/NB:2016 (Netherlands)
NS EN 1992-1 -1:2004-NA:2008 (Norway)
PN EN 1992-1-1/NA:2010 (Poland)
NP EN 1992-1-1/NA:2010-02 (Portugal)
SR EN 1992-1-1:2004/NA:2008 (Romania)
SS EN 1992-1-1/NA:2008 (Sweden)
SS EN 1992-1-1/NA:2008-06 (Singapore)
STN EN 1992-1-1/NA:2008-06 (Slovakia)
SIST EN 1992-1-1:2005/A101:2006 (Slovenia)
UNE EN 1992-1-1/NA:2013 (Spain)
CSN EN 1992-1-1/NA:2016-05 (Czech Republic)
BS EN 1992-1-1:2004/NA:2005 (United Kingdom)
TKP EN 1992-1-1:2009 (Belarus)
CYS EN 1992-1-1:2004/NA:2009 (Cyprus)
In addition to the National Annexes (NA) listed above, you can define a specific NA, applying user‑defined limit values and parameters.
Sensible and complete presetting of input parameters
Punching design on columns, wall ends, and wall corners
Optional arrangement of an enlarged column head
Automatic recognition of the position of the punching node from the RFEM model
Detection of curves or splines as boundary of the control perimeter
Automatic consideration of all slab openings defined in the RFEM model
Structure and graphical display of the control perimeter before calculation starts
Qualitative determination of punching shear reinforcement
Optional design with unsmoothed shear stress along the control perimeter that corresponds to the actual shear stress distribution in the FE model
Determination of the load increment factor β via full-plastic shear distribution as constant factors according to EN 1992‑1‑1, Sect. 6.4.3 (3), based on EN 1992‑1‑1, Fig. 6.21N or by user‑defined specification
Integration of design software by Halfen, a producer of shear rails
Numerical and graphical display of results (3D, 2D, and in sections)
Punching shear design with or without punching shear reinforcement
Optional consideration of minimum moments according to EN 1992‑1‑1 when determining longitudinal reinforcement
Design or analysis of longitudinal reinforcement
Complete integration of results in the RFEM printout report
The geometry is entered by means of templates, as in all other programs of the RX‑TIMBER family. By selecting the roof structure, you define the base geometry, which can be adjusted by user-defined settings. The relevant timber grade of the material can be selected from the material library. All material grades for glulam, hardwood, poplar and softwood timber specified in EN 1995-1-1 are available. Furthermore, it is possible to generate a strength class with user-defined material properties in order to extend the library.
Since the stiffening bracing includes the steel cross-sections, current steel grades are integrated in the library as well. Therefore, rolled and welded cross-sections are also available. Stiffening of coupling elements can be considered in Table 1.5 Connections as translational and rotational spring stiffnesses. The program handles these stiffnesses with a stiffness divided by the partial safety factor for the design of the bearing capacity and with the mean values of the stiffness for the serviceability limit state design. The loading can be entered directly as a lateral load (equivalent lateral load) resulting from a truss girder design.
The wind load is applied automatically to all four sides of the structure. Additionally, you can specify user-defined loads; for example, concentrated loads from columns (buckling load). According to the generated loads, the program automatically creates combinations for the ultimate and serviceability limit states as well as for fire resistance design in the background. The generated combinations can be considered or adjusted by user-defined specifications.
Definition of any additional support and free selection of degrees of freedom (additional free definition of translational and rotational spring stiffness of supports and hinges)
Arrangement of up to five collar/tie beams, including intermediate support for duopitch roof
Automatic generation of wind and snow loads
Automatic generation of required combinations for the ultimate and serviceability limit states, as well as fire resistance design (additional definition of several member and nodal loads)
For design according to EC 5 (EN 1995), the following National Annexes are available:
Germany DIN EN 1995-1-1/NA:2013-08 (Germany)
NBN EN 1995-1-1/ANB:2012-07 (Belgium)
BDS EN 1995-1-1/NA:2012-02 (Bulgaria)
DK EN 1995-1-1/NA:2011-12 (Denmark)
SFS EN 1995-1-1/NA:2007-11 (Finland)
NF EN 1995-1-1/NA:2010-05 (France)
I S. EN 1995-1-1/NA:2010-03 (Ireland)
UNI EN 1995-1-1/NA:2010-09 (Italy)
NEN EN 1995-1-1/NB:2007-11 (Netherlands)
ÖNORM B 1995-1-1:2015-06 (Austria)
PN EN 1995-1-1/NA:2010-09 (Poland)
SS EN 1995-1-1 (Sweden)
STN EN 1995-1-1/NA:2008-12 (Slovakia)
SIST EN 1995-1-1/A101:2006-03 (Slovenia)
CSN EN 1995-1-1:2007-09 (Czech Republic)
BS EN 1995-1-1/NA:2009-10 (the United Kingdom)
CYS EN 1995-1-1/NA:2011-02 (Cyprus)
Simple geometry input with illustrative graphics
Input of tapered cantilevers with cut-to-grain on the bottom side of rafters
Extensive material library that can be extended by user-defined materials
Determination of design ratios, support forces, and deformations
Color reference scales in result tables
Direct data export to MS Excel
Program languages: English, German, Czech, Italian, Spanish, French, Portuguese, Polish, Chinese, Dutch, and Russian
Verifiable printout report, including all required designs. Printout report available in many output languages; for example, English, German, French, Italian, Spanish, Russian, Czech, Polish, Portuguese, Chinese, and Dutch.
Optional consideration of stiffening elements for transversal tension
Two design types available for stiffening elements concerning transversal tension:
Constructive if required
Full absorption of tension stresses perpendicular to grain
Calculation of required number of stiffening elements for transversal tension and graphical representation of the arrangement in the beam
Simple geometry input with illustrative graphics
Convenient generation of snow loads according to EN 1991-1-3 or DIN 1055:2005, Part 5
Automatic determination of wind loads according to EN 1991-1-4 or DIN 1055:2005, Part 4
User-defined load cases and load applications
Automatic generation of all possible load combinations
Connection to MS Excel and access via COM interface
Material library for both standards
For design according to EC 5 (EN 1995), the following National Annexes are available:
DIN EN 1995-1-1/NA:2013-08 (Germany)
NBN EN 1995-1-1/ANB:2012-07 (Belgium)
DK EN 1995-1-1/NA:2011-12 (Denmark)
SFS EN 1995-1-1/NA:2007-11 (Finland)
NF EN 1995-1-1/NA:2010-05 (France)
UNI EN 1995-1-1/NA:2010-09 (Italy)
NEN EN 1995-1-1/NB:2007-11 (Netherlands)
ÖNORM B 1995-1-1:2015-06 (Austria)
PN EN 1995-1-1/NA:2010-09 (Poland)
SS EN 1995-1-1 (Sweden)
STN EN 1995-1-1/NA:2008-12 (Slovakia)
SIST EN 1995-1-1/A101:2006-03 (Slovenia)
CSN EN 1995-1-1:2007-09 (Czech Republic)
BS EN 1995-1-1/NA:2009-10 (the United Kingdom)
Extensive library of permanent loads
Allocation of a structure to service class, and specification of service class categories
Determination of design ratios, support forces, and deformations
Info icon indicating successful or failed design
Color reference scales in result tables
Direct data export to MS Excel
DXF interface for preparation production documents in CAD
Program languages: English, German, Czech, Italian, Spanish, French, Portuguese, Polish, Chinese, Dutch, and Russian
Verifiable printout report, including all required designs. Printout report available in many output languages; for example, English, German, French, Italian, Spanish, Russian, Czech, Polish, Portuguese, Chinese, and Dutch.
When determining internal forces, you can choose between calculation method 1 (uncracked over entire beam length) and calculation method 2 (crack formation over internal columns).
In both cases, it is possible to consider a constant effective width of the concrete slab over the entire span according to ENV 1994-1-1, 4.2.2.1 (1) and a redistribution of the moments. Internal forces for the design of shear connectors can only be determined by the elastic calculation of internal forces using the RSTAB analysis core (no RSTAB license is required).
The calculation performs fully automatic determination of the effective cross-section properties at the respective points of time, considering creep and shrinkage. In the RSTAB user interface, the structural models are created as a member structure, including all boundary conditions and loading. This way, reliable calculation of the internal forces with the effective cross-section properties is ensured.
It is possible to specify nonlinearities of member end releases (yielding, tearing, slippage, and so on) and supports (including friction). There are special dialog boxes available for determining the spring stiffnesses of columns and walls based on the geometry specifications.
Design of knee joints, T-joints, cross joints, and continuous column connections with I-shaped sections
Import of geometry and load data from RFEM/RSTAB or manual specification of the connection (for example, for recalculation without an existing RFEM/RSTAB model)
Flush top connections or connections with bolt row in extension
Design of positive and negative frame joint moments
Various inclinations of right and left horizontal beams as well as application to frames of duopitch and monopitch roofs
Consideration of additional flanges in a horizontal beam, for example for tapered sections
Symmetrical and asymmetrical T-joints or cross joints
Two-sided connection with different cross-section depth on the right and left
Automatic preliminary design of bolt layout and required stiffening
Optional design mode with possibility to specify all bolt spacing, welds, and sheet thicknesses
Screwability check with adjustable dimensions of used wrenches
Connection classification by stiffness and calculation of the spring stiffness of connections considered in the internal forces determination
Check up to 45 individual designs (components) of the connection
Automatic determination of governing internal forces for each individual design
Controllable connection graphics in rendering mode with specifications of material, sheet thickness, welds, bolt spacing, and all dimensions for construction
Integrated and flexibly extensible settings of National Annexes according to EN 1993-1-8 standard
Automatic conversion of internal forces from structural analysis into respective sections, also for eccentric member connections
Automatic determination of initial stiffness Sj,ini of the connection
Detailed plausibility check of all dimensions, including specifications of input limits (for example, for edge distances and hole spacing)
Optional application of compression forces to a column through contact
Possibility to update the cross-section depth of horizontal beams in case of tapered connections after connection geometry optimization in RF-/FRAME-JOINT Pro
Comprehensive and easy options in the individual input windows facilitate the representation of the structural system:
Nodal Supports
The support type of each node is editable.
It is possible to define a warp stiffening on each node. The resulting warp spring is determined automatically using the input parameters.
Elastic member foundation
In the case of elastic member foundations, you can manually enter spring constants.
Alternatively, you can use the various options to define the rotational and translational springs from a shear panel.
Member End Springs
RF-/FE-LTB calculates the individual spring constants automatically. You can use the dialog boxes and detailed pictures to represent a translational spring by connecting component, a rotational spring by a connecting column, or a warping stiffener (available types: end plate, channel section, angle, connecting column, cantilevered portion).
Member Hinges
If there are no member hinges defined in RFEM/RSTAB for the set of members, you can define them directly in the RF-/FE-LTB add-on module.
Load Data
The nodal and member loads of the selected load cases and combinations are displayed in separate windows. There you can edit, delete, or add them individually.
Imperfections
RF-/FE-LTB automatically applies the imperfections by scaling the lowest eigenvector.